Research · Building functional objects

Impact-absorbing plate lattices and helmet liners

Plate lattices and 3D-printed helmet liners designed by simulation and optimization to absorb impacts across a range of energies, now being commercialized by the startup Fortifyd.

The key idea. Protective gear works best when it is designed for the person wearing it and the hits they will take. Most helmets use the same foam for everyone. Instead, we use computer simulation to test thousands of 3D-printable lattice designs and pick the one that best protects a specific head shape against the impacts it is likely to face.

A 3D-printed helmet liner made of a curved grid of thin gray walls
A 3D-printed plate-lattice helmet liner. The lattice follows the curve of the head, and its walls are tuned for the impacts the helmet should absorb.

Plate lattices

A plate lattice is built from thin walls instead of struts. When an impact compresses it, the walls buckle and fold in a controlled way, so the force on whatever it protects stays nearly constant instead of spiking the way it does once foam is fully crushed. This builds on plate-lattice research in our lab by Smith et al., which showed that plate lattices absorb up to six times more energy than foams of the same density [1]. Two geometric parameters matter most: the wall thickness and the pre-buckle, a small built-in wave that sets how easily the walls start to fold.

Photo of a yellow printed honeycomb-like lattice with wavy walls, annotated with impact arrows, wall thickness, and pre-buckle e, and notes that it absorbs well in a single direction, is anisotropic, and has tunable geometric parameters
A printed plate lattice. Wall thickness and pre-buckle (e) are the main geometric parameters. Plate lattices absorb impacts very well in one direction.
Two line drawings of plate lattices, one with nearly straight walls labeled e equals 0.05 needing 70 joules to trigger buckling and better for high energy impacts, and one with wavier walls labeled e equals 0.35 needing 10 joules and better for low energy impacts
Tuning for the impact. A nearly straight wall (e = 0.05) needs a 70 J impact to start buckling and suits hard hits. A more pre-buckled wall (e = 0.35) starts at 10 J and suits soft hits.

Designing by simulation

Choosing these parameters by hand works for a test block, but not for a helmet liner that has to handle several expected impacts at once. With a master’s student I mentored, I developed an automated design pipeline that generates lattice geometry from design parameters, simulates the impact with finite element analysis, scores the absorption profile, and hands the result to an optimizer. Gradient-free optimization searches broadly across the design space, and gradient-based optimization refines the most promising designs. Thousands of simulations run on a computing cluster, and a machine-learning surrogate trained on them lets the search evaluate millions of candidate designs instead of thousands. Pre-buckle can also be graded through a lattice, so different layers respond to different impact energies.

Cycle diagram with Optimization producing design parameters, Geometry Generation producing finite elements, and Simulation producing an absorption profile that returns to Optimization
Automated design synthesis. An optimizer proposes design parameters, the lattice geometry is generated, finite element simulation predicts how it absorbs the impact, and the absorption profile feeds the next round.
Six unit-cell renders (body-centered cubic, face-centered cubic, diamond, Kelvin cell, re-entrant, and the plate lattice) beside a scatter plot of efficiency at a 70 joule impact versus efficiency at a 7 joule impact, where the graded plate lattice front lies above the ungraded plate lattice front, and both lie well above the strut lattice front
Plate lattices against common strut lattices. Each point is one simulated design, scored on how efficiently it handles a 7 J impact (horizontal) and a 70 J impact (vertical). Lines trace the best trade-offs for strut lattices (body-centered cubic, face-centered cubic, diamond, Kelvin cell, and re-entrant) and for our plate lattice with and without graded pre-buckle. A tenfold difference in energy is hard for one geometry to handle, and the plate lattices do it best, especially when graded.
Simulation checked against experiment. Finite element simulations (top) and high-speed video of drop tests (bottom) for two plate-lattice wall designs, played in sync.

Helmet liners

The same pipeline designs complete helmet liners. A plate lattice is mapped conformally into the space between the head and the helmet shell, tuned for the impacts the helmet should absorb, and printed. Printed liners showed up to 6× lower peak acceleration than standard EPS foam liners in drop tests, and they recovered 95% of their impact absorption within two minutes, so unlike foam they keep protecting after repeated hits. I also cut the time to model and export a complete liner from about 10 hours to 8 minutes.

Rendering of a vertical drop tower with a helmeted headform above an anvil, labeled load cell headform, accelerometer, AprilTag, high-speed camera, and load cell anvil
Drop tower. Load cells in the headform and anvil, an accelerometer, and a high-speed camera measure each impact.
Photo of a white test headform with a load cell on top, strapped into a printed gray and green helmet liner
A printed liner on the test headform, ready for drop testing.

Fortifyd

Fortifyd is a startup that grew out of this plate-lattice research in the Matter Assembly Computation Lab. As its lead software engineer, I am responsible for the computational design and optimization software, and I deploy it with an industrial partner through training and ongoing support. In eight months the work advanced from technology readiness level 3 to 5, and in 2026 Fortifyd won first place and $200,000 in CU Boulder Venture Partners’ Lab Venture Challenge.

[1] L. Smith, B. Hayes, K. Ford, E. Smith, D. Flores, and R. MacCurdy, "Tunable Metamaterials for Impact Mitigation," Advanced Materials Technologies 9, 2301668 (2024). doi:10.1002/admt.202301668

Publications

  1. Digital Light Processing of Liquid Crystalline Elastomer Plate Lattice Metamaterials for Energy Dissipation
    Jeremy A. Herman, Charles Wade, Bryan Kaehr, Devin Roach, Robert MacCurdy, and Timothy White
    2026
    In submission